individual house elevation
60×82-ft-house-front-elevation-design-for-double-floor-plan

Planning For a 60×82 Ft House Front Elevation Design For Double Floor Plan

You have found a home plan with incredible architectural qualities with the purchase of your dream home. Now, you have to look at it at a quarter-inch level, and determine if your eyes are going to stay awake at night as you gaze at the plan. The first question you must ask yourself is, “How much house front elevation is necessary?” Next, you need to determine what square footage you want for this floor plan area. Lastly, you need to find a contractor who can design the house front elevation design for double floor plan correctly.

In order to know how much square footage you will have for this design area, you must first know the required house front elevation design for double floor plans. This measurement comes from the lowest point of the roof on the inside walls to the highest point on the outside wall in the middle of the house. It also includes the middle cedar shake that is located between the roof and the exterior wall. The slope on this part of the roof also determines the amount of elevation needed for your home. Remember that the total square footage of the house will also depend on the number of floors you have.

Once you determine the required ground level for this plan, then you must determine the amount of “wattage” you will have to work with. What wattage means is the amount of electricity that is used by the home during the day. Remember, most homes use eighty-five percent of their electricity during the day. This means that you will need at least one thousand watts of lighting for each floor. Also, if you are going to have any kind of extra electrical outlets, then they will need to be located in the proper location. Also, you may want to find an installer who will help you determine the required square footage for floor plan installation.

After you know the required square footage and the required power requirements for your home, you can begin to determine the location of the house front elevation on your property. The best place for the house front elevation of your new home will be where you have easy access to both the exterior of your home as well as to a street or other type of driveway. If you decide to build on a gravel foundation, then you should also make sure that the house front is at an angle that will allow the gravel to run off easily.

When you are using the measurements to figure out the required square footage, you should also include the length of the driveway or paved walkways that you plan on using. When you are building on a gravel foundation, then there is nothing you can do to avoid the inevitable. The longer the driveway, the more difficult it will be to clear the area. However, if you make the necessary adjustments, then it can be made to look like a perfectly straight walkway even if it is not. The measurements that are included in your floor plan are the width and length of the driveway and the length of the patio and poolside walkway to be included in the calculations of your house front elevation.

Your calculations are going to be dependent upon the exact square footage of your plot, which is why you need to use accurate measurements. Your calculations will determine how much ground you have to plat and this is based on the total area of your home including the basement. To get the correct measurements for your house front elevation design for double floor plans, you can use either the elevations provided by a software program like Home Inspector Pro, or you can take it a step further and create a set of plans on your own.

After you have the square footage and the length of the driveway that you want included in your calculation, you will have to add the width of your house. If you are working with a landscape architect, you will find that the actual measurements are very important. You should make sure that everything fits as intended when building your house front elevation design for double floor plans. It would be extremely disappointing if you have a beautiful front yard and find that the patio that you wanted to go along with it is too narrow. This would defeat the purpose of having a larger house in the first place.

Once you have calculated all of the measurements and you have them ready to go, you can start to layout the site of your new home. When you are trying to design the site of your home to fit into the space you have, you will want to take into consideration the length of the house and also the width of your walkway. When planning your house front elevation design for double floor plans, you must take all of these things into consideration. Once you have done so, you will be ready to get started and begin planning for the perfect outdoor area. Check the internet for more information on how to design a great outdoor area to bring you closer to nature.

60×82 ft house front elevation design for double floor plan

 

House plan  details

 

Plot size =>  60*82 ft 4920 sq ft

Direction => North

 

Ground floor

 

2 bedroom =>14’9*12’10 ft, 14’9*10’3 ft ,

1 servant’s room =>10’4*9’10 ft

2 attach toilet =>6’0*9’2 ft, 7’3*5’6 ft

2 common toilet => 4’3*6’6 ft , 3’6*6’0 ft

2  dressing  =>7’0*9’2 ft , 5’4*7’2 ft

1 dinning and drawing room =>17’0*24’1 ft

1 Kitchen =>14’6*11’3 ft

1 store => 8’1*6’4 ft

wash area =>5’5* 10’2 ft

1 living hall =>14’7*16’3 ft

1 pooja room =>5’0*11’4 ft

1 office => 9’8*11’4 ft

garden =>12’9*16’9 ft

entrance cut off lobby => 4’5*16’3 ft

car parking  =>22’11*50’0 ft

Staircase => inside

 

first floor

 

3 bedroom =>14’9*12’10 ft, 14’9*10’3 ft , 10’6*12’9 ft

1 servant’s room =>10’4*9’10 ft

2 attach toilet =>6’0*9’2 ft, 7’3*5’6 ft

2 common toilet => 4’3*6’6 ft , 3’6*6’0 ft

2  dressing  =>7’0*9’2 ft , 5’4*7’2 ft

1 dinning and drawing room =>17’0*24’1 ft

1 Kitchen =>14’6*11’3 ft

1 store => 8’1*6’4 ft

wash area =>5’5* 10’2 ft

front open terrace

 

60×82 ft house front elevation design for double floor plan

  subscribe our youtube channel  

contact now